Installing your TruPoint Orange doctor blade incorrectly will result in disaster. Well, not really. But it create headaches for the press operator and waste valuable resources. It will also prevent you from getting the maximum value from your doctor blade investment.

The TruPoint Orange doctor blade is a lifesaver in many pressrooms when it comes to eliminating UV ink spitting and start-up lines, reducing the frequency of blade changes and offering a safe alternative to steel blades. However, the blade requires a bit more finesse than steel when it’s being installed in order to work its magic.

Principles of proper doctor blade installation


But, if we had to name the three most important factors to keep in mind when installing a TruPoint Orange doctor blade, it would be handling, orientation and pressure. That’s not to say that other considerations such as angle and alignment aren’t important. It’s just that these particular variables, if not executed properly, will almost always foretell the failure of the blade.


A press operator should take care to protect the integrity of any doctor blade (and his or her own safety when using steel) during blade transit, storage and installation. But particular caution should be exercised to keep a MicroTip® edge from coming in contact with anything that may damage it.

The MicroTip on an Orange blade is amazing in its ability to achieve and maintain a fine area of contact with the anilox roll surface. After all, this is the driving force behind the blade’s ability to match the metering performance of a steel blade. Its material is also incredibly tough, able to stand up to the abrasiveness of even the harshest chemistries like high titanium white inks and special coating formulas. But some of the same characteristics that give the TruPoint Orange doctor blade its awesome wiping power and durability also make its MicroTip vulnerable to nicks when handled or stored improperly. Once the edge is compromised, the blade can cause printing defects such as continuous streaks, marks and lines on the substrate. Keep the blade safe and always run your finger along the leading edge of the blade to ensure no imperfections are present before locking it into place. (Remember, there is no danger of cutting yourself with a TruPoint Orange doctor blade!)


要充分发挥 TRUpointOrange 刀片的性能优势,必须以正确的方向安装刀片。安装时 TruPointOrange 刀片上印有文字,以便在安装时为您提供指导。重要的是,MicroTip 边缘要尖。 远离 将刀片放在辊子上,文字朝向您,箭头指向网纹辊。这很简单--如果你看不清文字,就说明刀片的安装方式不对。安装 "反向 "的刀片(MicroTip ,刀片朝向您的方向)可能会使您看不清文字。 the roll), will not make even contact along the anilox roll and result in streaking on the printed piece. If your Orange blade is beveled, the bevel should face the inside of the chamber, or away from the roll, when properly installed. If using a doctor blade chamber, the containment blade should be the first to touch the anilox roll and the metering blade, second.


Assuming a doctor blade chamber is properly aligned, much less blade pressure is needed to get a clean wipe of the roll with a plastic doctor blade than with a steel one. For best results, find the minimum amount of blade pressure required to contact the anilox surface when installing TruPoint Orange. Unlike with steel, TruPoint Orange should generate few or no streaks on the anilox when starting up. Minimizing blade pressure against the anilox roll will not only ensure print quality but also extend blade life (and end seal life if applicable).

A good way to gauge the correct amount of doctor blade pressure is to look at the roll once it’s inked. Before the clamp is tightened, the anilox roll will appear glossy – a sign that too much ink is remaining on the surface. Blade pressure should be increased gradually until a satin finish appears on the surface of the roll. A dull sheen is a good indication that the correct amount of pressure has been achieved and the doctor blade is effectively shearing the excess ink from the roll. If pressure is increased beyond this point, the doctor blade edge will bend, and contact area with the roll will grow. The anilox surface will begin to look glossy again or show light streaks or lines because it is being flooded with too much ink. At this point, 减轻刀片压力、 而不是增加,就能缓解这一问题。

When a TruPoint Orange blade is installed properly, its metering power is brilliant in terms of executing consistent print quality over the life of the blade. Take care to ensure the three key elements of success – proper blade handling, correct blade orientation and the right amount of blade pressure – and your TruPoint Orange doctor blade will likely become your press operator’s new best friend.

打印、PDF 和电子邮件